EN Standard Hydraulic Hose – Spiral or Braid Reinforcement for Higher Pressure

EN standard hydraulic hose is another standard all over the world. It has different reinforcement structures, such as different braid or spiral layers to increase the pressure of hydraulic hose. Here are commonly used EN standard hydraulic hose, including structures, drawings, specs and applications.

EN 853 1SN Steel Wire Reinforced Hydraulic Rubber Hose

Introduction

EN 853 1SN single wire braided hydraulic hose is mainly used in high pressure hydraulic systems. The difference between 1ST and 1SN is that the later type has thinner covers. So type 1SN is not suitable for applications that requires remove.

High tensile steel wire braid reinforcement provides high working pressure and ozone and weather resistant synthetic rubber cover protecting the inside reinforcement and tube from abrasion and corrosion. It is suitable for carrying fluids such as glycol, mineral oil, fuel, lubricants, emulsion, hydrocarbon etc.

A drawing of EN 853 1SN hydraulic hose with one-braid high tensile steel wire.

ENHH-01: EN 853 1SN hydraulic hose drawing.

Two EN 853 1SN hydraulic hoses on table: one shows the spec and the other shows section structure.

ENHH-02: EN 853 1SN hydraulic hose with one-braid high tensile steel wire reinforcement.

Construction

  • Tube: high quality synthetic rubber compounds.
  • Reinforcement: one-braid high tensile steel wire.
  • Cover: abrasion and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F).
Table 1: EN 853 1ST/1SN Steel Wire Reinforced Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
A AT
mm inch dash min. max. min. max. min. max. max. MPa psi MPa psi MPa psi mm kg/m
EN8531S-01 5 3/16 -3 4.6 5.4 9.0 10.0 11.9 13.5 12.5 25 3625 50 7250 100 14500 90 0.20
EN8531S-02 6.3 1/4 -4 6.2 7.0 10.6 11.6 15.1 16.7 14.1 22.5 3260 45 6525 90 13050 100 0.25
EN8531S-03 8 5/16 -5 7.7 8.5 12.1 13.3 16.7 18.3 15.7 21.5 3120 43 6235 85 12325 115 0.31
EN8531S-04 10 3/8 -6 9.3 10.1 14.5 15.7 19.0 20.6 18.1 18 2610 36 5220 72 10440 130 0.36
EN8531S-05 12.5 1/2 -8 12.3 13.5 17.5 19.1 22.2 23.8 21.4 16 2320 32 4640 64 9280 180 0.45
EN8531S-06 16 5/8 -10 15.5 16.7 20.6 22.2 25.4 27.0 24.5 13 1885 26 3770 52 7540 200 0.52
EN8531S-07 19 3/4 -12 18.6 19.8 24.6 26.2 29.4 31.0 28.5 10.5 1520 21 3045 42 6090 240 0.65
EN8531S-08 25 1 -16 25.0 26.4 32.5 34.1 37.1 39.1 36.6 8.8 1280 17.5 2540 35 5075 300 0.91
EN8531S-09 31.5 1-1/4 -20 31.4 33.0 39.3 41.7 44.4 47.6 44.8 6.3 910 15 2175 25 3625 420 1.30
EN8531S-10 38 1-1/2 -24 37.7 39.3 45.6 48.0 50.8 54.0 52.1 5 725 10 1450 20 2900 500 1.70
EN8531S-11 51 2 -32 50.4 52.0 58.7 61.7 65.1 68.3 65.5 4 580 8 1160 16 2320 630 2.00

EN 853 2SN Steel Wire Reinforced Hydraulic Rubber Hose

Introduction

EN 853 2SN hydraulic rubber hose is reinforced by two-braid high tensile steel wires to support high working pressures – up to 6020 psi at 3/16" I.D.. Oil resistant tube and ozone & abrasion resistant cover contribute long-term service life. It is available to convey water based and petroleum based hydraulic fluids within -40°C to 100°C (max. 120 °C intermittent).

They are widely used in offshore, forestry, factories and similar applications where abrasion resistance requirements is strict.

A drawing of EN 853 2SN hydraulic hose with two-braid high tensile steel wires.

ENHH-03: EN 853 2SN hydraulic hose drawing.

A side view of EN 853 2SN hydraulic hose and we can see the spec on surface and section structure.

ENHH-04: EN 853 2SN hydraulic hose has two-braid high tensile steel wires.

Construction

  • Tube: high quality synthetic rubber compounds.
  • Reinforcement: two-braid high tensile steel wires.
  • Cover: abrasion and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F).
Table 2: EN 853 2ST/2SN Steel Wire Reinforced Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
A AT
mm inch dash min. max. min. max. min. max. max. MPa psi MPa psi MPa psi mm kg/m
EN8532S-01 5 3/16 -3 4.6 5.4 10.6 11.6 15.1 16.7 14.1 41.5 6020 83 12035 165 23925 90 0.32
EN8532S-02 6.3 1/4 -4 6.2 7.0 12.1 13.3 16.7 18.3 15.7 40 5800 80 11600 160 23200 100 0.36
EN8532S-03 8 5/16 -5 7.7 8.5 13.7 14.9 18.3 19.9 17.3 35 5075 70 10150 140 20300 115 0.45
EN8532S-04 10 3/8 -6 9.3 10.1 16.1 17.3 20.6 22.2 19.7 33 4785 66 9570 132 19140 130 0.54
EN8532S-05 12.5 1/2 -8 12.3 13.5 19.0 20.6 23.8 25.4 23.0 27.5 3990 55 7975 110 15950 180 0.68
EN8532S-06 16 5/8 -10 15.5 16.7 22.2 23.8 27.0 28.6 26.2 25 3625 50 7250 100 14500 200 0.80
EN8532S-07 19 3/4 -12 18.6 19.8 26.2 27.8 31.0 32.6 30.1 21.5 3120 43 6235 85 12325 240 0.94
EN8532S-08 25 1 -16 25.0 26.4 34.1 35.7 38.5 40.9 38.9 16.5 2390 32.5 4710 65 9425 300 1.35
EN8532S-09 31.5 1-1/4 -20 31.4 33.0 43.3 45.7 49.2 52.4 49.5 12.5 1810 25 3625 50 7250 420 2.15
EN8532S-10 38 1-1/2 -24 37.7 39.3 49.6 52.0 55.6 58.8 55.9 9 1305 18 2310 36 5220 500 2.65
EN8532S-11 51 2 -32 50.4 52.0 62.3 64.7 68.2 71.4 68.6 8 1160 16 2320 32 4640 630 3.42

EN 857 1SC Steel Wire Reinforced Hydraulic Rubber Hose

Introduction

EN 857 1SC hydraulic hose has similar performance with its counterpart SAE 100R1 besides tighter bending radius. It is reinforced by one-braid high tensile wire. Ozone and weather resistant cover separates the tube from the outside environment and effectively extends the service life of hydraulic hose. Single wire braided 1SC high pressure hydraulic hose is suitable for high pressure conditions where tight routing is required.

A drawing of EN 857 1SC hydraulic hose with one-braid high tensile steel wire.

ENHH-05: EN 857 1SC hydraulic hose drawing.

Two black color EN 857 hydraulic hose with specs on the hose surface.

ENHH-06: EN 857 1SC hydraulic hose.

Construction

  • Tube: oil resistant synthetic rubber.
  • Reinforcement: One-braid high tensile steel wire.
  • Cover: abrasion and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F).
Table 3: EN 857 1SC Steel Wire Reinforced Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. min. max. max. MPa psi MPa psi MPa psi mm kg/m
EN8571S-01 6.3 1/4 -4 6.1 6.9 9.6 10.8 13.5 22.5 3260 45 6525 90 13050 75 0.20
EN8571S-02 8 5/16 -5 7.7 8.5 10.9 12.1 14.5 21.5 3120 43 6235 86 12470 85 0.15
EN8571S-03 10 3/8 -6 9.3 10.1 12.7 14.5 16.9 18 2610 36 5220 72 10440 90 0.19
EN8571S-04 12.5 1/2 -8 12.3 13.5 15.9 18.1 20.4 16 2320 32 4640 64 9280 130 0.23
EN8571S-05 16 5/8 -10 15.5 16.7 19.8 21.0 23.0 13 1885 26 3770 52 7540 150 0.29
EN8571S-06 19 3/4 -12 18.6 19.8 23.2 24.4 26.7 10.5 1520 21 3045 42 6090 180 0.34
EN8571S-07 25 1 -16 25.0 26.4 30.7 31.9 34.9 8.8 1280 17.6 2550 35.2 5100 230 0.49

EN 857 2SC Steel Wire Reinforced Hydraulic Rubber Hose

Introduction

EN 857 2SC hydraulic rubber hose serves high pressure hydraulic system where tight bends and maximum abrasion resistance performance is urgently needed. This type hydraulic hose owns oil resistant inner tube, which will not deform when transporting water based and petroleum based hydraulic fluids within -40 °C to +100 °C. The two-braid high tensile steel wires support high working pressure with tight bend radius. Chemicals and weather resistant cover guard long service life of the whole hose.

A drawing of EN 857 2SC hydraulic hose with two-braid high tensile steel wires.

ENHH-07: EN 857 2SC hydraulic hose drawing.

Four EN 857 2SC hydraulic hoses with specs on the hose surface.

ENHH-08: EN 857 2SC hydraulic hose.

Construction

  • Tube: oil resistant synthetic rubber.
  • Reinforcement: one-braid high tensile steel wires.
  • Cover: abrasion and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F).
Table 4: EN 857 2SC Steel Wire Reinforced Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. min. max. max. MPa psi MPa psi MPa psi mm kg/m
EN5872S-01 6.3 1/4 -4 6.1 6.9 10.6 11.7 14.2 40 5800 80 11600 160 23200 75 0.30
EN5872S-02 8 5/16 -5 7.7 8.5 12.1 13.3 16.0 35 5075 70 10120 140 20300 85 0.34
EN5872S-03 10 3/8 -6 9.3 10.1 14.4 15.6 18.3 33 4785 66 9570 132 19140 90 0.42
EN5872S-04 12.5 1/2 -8 12.3 13.5 17.5 19.1 21.5 27.5 3990 55 7975 110 15950 130 0.54
EN5872S-05 16 5/8 -10 15.5 16.7 20.5 22.3 24.7 25 3625 50 7250 100 14500 170 0.68
EN5872S-06 19 3/4 -12 18.6 19.8 24.6 26.4 28.6 21.5 3120 43 6235 86 12470 200 0.80
EN5872S-07 25 1 -16 25.0 26.4 32.5 34.3 36.6 16.5 2390 33 4785 66 9570 250 1.15

EN 856 4SH Steel Wire Spiraled Hydraulic Rubber Hose

Introduction

EN 856 4SH steel wire spiraled hydraulic rubber hose consists of an inner tube of oil resistant synthetic rubber, four spiral layers of spiral wires reinforcement and is covered with oil and weather resistant synthetic rubber. Spiral hydraulic hose shares outstanding kick resistance, impulse resistance and can support surge pressure. EN 856 4SH hydraulic hose is widely used in applications where high pressure, high abrasion and kick resistance are urgently required. It is also be used in petroleum based hydraulic fluids within a temperature ranging from -40 °C to +100 °C.

A drawing of EN 856 4SH hydraulic hose with four-spiral high tensile steel wires.

ENHH-09: EN 856 4SH hydraulic hose drawing.

A section structure of EN 856 4SH hydraulic hose on the white background.

ENHH-10: EN 856 4SH hydraulic hose with four-spiral high tensile steel wire.

Construction

  • Tube: high quality synthetic rubber compounds.
  • Reinforcement: four-spiral high tensile steel wires.
  • Cover: abrasion and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F).
Table 5: EN 856 4SH Steel Wire Spiraled Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. min. max. min. max. MPa psi MPa psi MPa psi mm kg/m
EN8564S-01 19 3/4 -12 18.6 19.8 27.6 29.2 31.4 33.0 42 6090 87 12180 168 24360 280 1.70
EN8564S-02 25 1 -16 25.0 26.4 34.4 36.0 37.5 39.9 38 5510 76 11020 152 22040 340 2.50
EN8564S-03 31.5 1-1/4 -20 31.4 33.0 40.9 42.9 43.9 47.1 32.5 4710 65 9425 130 18850 460 3.00
EN8564S-04 38 1-1/2 -24 37.7 39.3 49.8 49.8 51.9 55.1 29 4205 58 8410 116 16820 560 3.60
EN8564S-05 51 2 -32 50.4 52.0 64.2 64.2 66.5 69.7 25 3625 50 7250 100 14500 700 5.00

EN 856 4SP Steel Wire Spiraled Hydraulic Rubber Hose

Introduction

EN 856 4SP hydraulic rubber hose is similar to EN 856 4SH hydraulic hose, but the working pressure (under the same working temperature) is higher than EN 856 4SH hose. Four-spiral high tensile spiral wire reinforcement structure gives the hose best abrasion resistance and impulse fatigue. This kind of reinforcement is ideal for outdoor applications like forestry and mine equipment.

Oil resistant synthetic rubber is widely used in water and petroleum based hydraulic fluids within -40 °C to +100 °C. If the working temperature is lower or higher than the temperature, the service life of the hose will be changed.

A drawing of EN 856 4SP hydraulic hose with four-spiral of high tensile steel wires.

ENHH-11: EN 856 4SP hydraulic hose drawing.

Two EN 856 4SP hydraulic hoses and we can see the section structure clearly.

ENHH-12: EN 856 4SP hydraulic hose.

Construction

  • Tube: high quality synthetic rubber compounds.
  • Reinforcement: four-spiral high tensile steel wires.
  • Cover: abrasion and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F).
Table 6: EN 856 4SP Steel Wire Spiraled Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. min. max. min. max. MPa psi MPa psi MPa psi mm kg/m
EN8564SP-01 6.3 1/4 -4 6.2 7.0 14.1 15.3 17.1 18.7 45 6525 90 13050 180 26100 150 0.64
EN8564SP-02 10 3/8 -6 9.3 10.1 16.9 18.1 20.6 22.2 44.5 6450 89 12905 178 25810 180 0.75
EN8564SP-03 12.5 1/2 -8 12.3 13.5 19.4 21.0 23.8 25.4 41.5 6020 83 12035 166 24070 230 0.89
EN8564SP-04 16 5/8 -10 15.5 16.7 23.0 24.6 27.4 29.0 35 5075 70 10150 140 20300 250 1.10
EN8564SP-05 19 3/4 -12 18.6 19.8 27.4 29.0 31.4 33.0 35 5075 70 10150 140 20300 300 1.50
EN8564SP-06 25 1 -16 25.0 26.4 34.5 36.1 38.5 40.9 28 4060 56 8120 112 16240 340 2.00
EN8564SP-07 31.5 1-1/4 -20 31.4 33.0 45.0 47.0 49.2 52.4 21 3045 42 6090 84 12180 460 3.00
EN8564SP-08 38 1-1/2 -24 37.7 39.3 51.4 53.4 55.6 58.8 18.5 2680 37 5365 74 10730 560 3.40
EN8564SP-09 51 2 -32 50.4 52.0 64.3 66.3 68.2 71.4 16.5 2390 33 4785 66 9570 660 4.35

When you contact us, please provide your detail requirements.

That will help us give you a valid quotation.