SAE Hydraulic Hose – Completed Structures for All Your Working Environments

As we all know, the SAE standard is an important standard in hydraulic hose design, construction and pressure rating to ensure that hydraulic hoses meet minimum construction requirements. Here are All completed SAE standard hydraulic hoses ranges from R1 to R17. You can refer to them according to the drawings, section structures and specs. Then choose the best one suitable for you.

If you need the EN standard hydraulic hose, click for another page: EN Standard Hydraulic Hose.

Or, you can refer to our catalogs, for all schedules of hydraulic hose.

SAE 100R1 Steel Wire Reinforced Hydraulic Rubber Hose

Introduction

SAE 100R1 single steel wire braided hose is a typical high pressure hydraulic hose and it is suitable for hydraulic lines or general industrial system. High tensile strength steel wire reinforcement makes SAE 100R1 hose support higher pressure than common steel wire.

SAE 100R1 rubber hose should be used with petroleum- and water-based hydraulic fluids within a temperature ranging from -40 °C to +100 °C.

A drawing of SAE 100 R1 hydraulic hose with one-braid of high tensile steel wire.

SAEH-01: SAE 100R1 hydraulic hose drawing.

A piece of SAE 100R1-AT hydraulic hose lying on white background, we can see the section structure.

SAEH-02: SAE 100R1-AT hydraulic hose.

Construction

  • Tube: black, oil resistant synthetic rubber.
  • Reinforcement: one-braid high tensile steel wire.
  • Cover: black, oil and abrasion resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F).

Specification

Table 1: SAE 100R1 Steel Wire Reinforced Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
A AT
mm inch dash min. max. min. max. min. max. max. MPa psi MPa psi MPa psi mm kg/m
SAER1-01 5 3/16 -3 4.6 5.4 8.9 10.1 11.9 13.5 12.5 21 3045 42 6090 84 12810 90 0.20
SAER1-02 6.3 1/4 -4 6.2 7.0 10.6 11.7 15.1 16.7 14.1 19.2 2780 38.5 5580 77 11165 100 0.25
SAER1-03 8 5/16 -5 7.7 8.5 12.1 13.3 16.7 18.3 15.7 17.5 2540 35 5075 70 10150 115 0.31
SAER1-04 10 3/8 -6 9.3 10.1 14.5 15.7 19.0 20.6 18.1 15.7 2280 31.5 4570 63 9135 125 0.36
SAER1-05 12.5 1/2 -8 12.3 13.5 17.5 19.0 22.2 23.8 21.5 14 2030 28 4060 56 8120 180 0.45
SAER1-06 16 5/8 -10 15.5 16.7 20.6 22.2 25.4 27.0 24.7 10.5 1520 21 3045 42 6090 205 0.52
SAER1-07 19 3/4 -12 18.6 19.8 24.6 26.2 29.4 31.0 28.6 8.7 1260 17.5 2540 35 5075 240 0.65
SAER1-08 25 1 -16 25.0 26.4 32.5 34.1 36.9 39.3 36.6 7 1015 14 2030 28 4060 300 0.91
SAER1-09 31.5 1-1/4 -20 31.4 33.0 39.3 41.7 44.4 47.6 44.8 4.3 620 8.7 1260 17.5 2540 420 1.30
SAER1-10 38 1-1/2 -24 37.7 39.3 45.6 48.0 50.8 54.0 52.0 3.5 510 7 1015 14 2030 500 1.70
SAER1-11 51 2 -32 50.4 52.0 58.7 61.9 65.1 68.3 65.9 2.6 380 5.2 750 10.5 1520 630 2.00

SAE 100R2 High Pressure Steel Wire Reinforced Hydraulic Rubber Hose

Introduction

SAE 100R2 high pressure steel wire reinforced hydraulic hose should be used with petroleum- and water-based hydraulic fluids within a temperature ranging from -40 °C to 100 °C. It consists of an inner tube of oil-resistant synthetic rubber, steel-wire reinforcement according to hose type, as detailed below, and an oil and weather resistant synthetic rubber cover. A ply, or braid, of suitable material may be used over the inner tube and/or over the wire reinforcement to fasten the synthetic rubber to the wire.

A drawing of SAE 100R2 hydraulic hose and we can see two-braid of high tensile steel wire reinforcement.

SAEH-03: SAE 100R2 hydraulic hose drawing.

A piece of black SAE 100R2 hydraulic hose shows the section structure clearly.

SAEH-04: SAE 100R2 hydraulic hose.

Application

  • It is ideal for outside working environments including offshore, forestry, construction and mining where high abrasion resistance is required.
  • Petroleum- and water based hydraulic fluids with high pressure can pass through the inner tube smoothly and freely without producing excessive heat and leak.
  • It is also found in mobile equipment including farm tractor, dump truck and in-plant hydraulic equipment.

Construction

  • Tube: black, oil resistant, Nitrile (NBR).
  • Reinforcement: two-braid high tensile steel wire.
  • Cover: Abrasion and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F).
Table 2: SAE 100R2 Steel Wire Reinforced Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
A AT
mm inch dash min. max. min. max. min. max. max. MPa psi MPa psi MPa psi mm kg/m
SAER2-01 5 3/16 -3 4.6 5.4 10.6 11.7 15.1 16.7 14.1 35 5075 70 10150 140 20300 90 0.32
SAER2-02 6.3 1/4 -4 6.2 7 12.1 13.3 16.7 18.3 15.7 35 5075 70 10150 140 20300 100 0.36
SAER2-03 8 5/16 -5 7.7 8.5 13.7 14.9 18.3 19.8 17.3 29.7 4310 59.5 8630 119 17255 115 0.45
SAER2-04 10 3/8 -6 9.3 10.1 16.1 17.3 20.6 22.2 19.7 28 4060 56 8120 112 16240 125 0.54
SAER2-05 12.5 1/2 -8 12.3 13.5 19 20.6 23.8 25.4 23.1 24.5 3550 49 7110 98 14210 180 0.68
SAER2-06 16 5/8 -10 15.5 16.7 22.2 23.8 27 28.6 26.3 19.2 2780 38.5 5580 77 11165 205 0.8
SAER2-07 19 3/4 -12 18.6 19.8 26.2 27.8 31 32.5 30.2 15.7 2280 31.5 4570 63 9135 240 0.94
SAER2-08 25 1 -16 25 26.4 34.1 35.7 38.5 40.9 38.9 14 2030 28 4060 56 8120 300 1.35
SAER2-09 31.5 1-1/4 -20 31.4 33 43.2 45.6 49.2 52.4 49.6 11.3 1640 22.7 3290 45.5 6600 420 2.15
SAER2-10 38 1-1/2 -24 37.7 39.3 49.6 52 55.6 58.7 56 8.7 1260 17.5 2540 35 5075 500 2.65
SAER2-11 51 2 -32 50.4 52 62.3 64.7 68.3 71.4 68.6 7.8 1130 15.7 2280 31.5 4570 630 3.42

SAE 100R3 Double Fiber Braid (Nonmetallic) Hydraulic Rubber Hose

Introduction

SAE 100R3 double fiber braid hydraulic rubber hose is ideal for medium pressure fuel and oil lines as well as return and suction hoses of hydraulic systems. It is constructed with an inner tube of oil-resistant synthetic rubber, a reinforcement consisting of a ply, or plies, of woven or braided textile fibers with a suitable spiral of body wire, and an oil and weather resistant synthetic rubber cover.

A drawing of SAE 100R3 hydraulic hose and we can see two-braid of fibers.

SAEH-05: SAE 100R3 hydraulic hose drawing.

A hydraulic hose shows the section structure clearly.

SAEH-06: SAE 100R3 hydraulic hose.

Construction

  • Tube: black, oil resistant, Nitrile (NBR).
  • Reinforcement: two-barid textile, which is pre-treated for tube and cover adhesion.
  • Cover: An oil and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F).
Table 3: SAE 100R3 Double Fiber Braid (Nonmetallic) Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. min. max. MPa psi MPa psi MPa psi mm kg/m
SAER3-01 5 3/16 -3 4.5 5.4 11.9 13.5 10.5 1520 21 3050 42 6090 75 0.16
SAER3-02 6.3 1/4 -4 6.1 7.0 13.5 15.1 8.7 1260 17.5 2540 35 5075 75 0.18
SAER3-03 8 5/16 -5 7.6 8.5 16.7 18.3 8.4 1220 16.8 2440 33.5 4860 100 0.27
SAER3-04 10 3/8 -6 9.2 10.1 18.3 19.8 7.8 1130 15.7 2280 31.5 4570 100 0.31
SAER3-05 12.5 1/2 -8 12.4 13.5 23.0 24.6 7 1015 14 2030 28 4060 125 0.45
SAER3-06 16 5/8 -10 15.6 16.7 26.2 27.8 6.1 885 12.2 1770 24.5 3550 140 0.53
SAER3-07 19 3/4 -12 18.7 19.8 31.0 32.5 5.2 750 10.5 1520 21 3045 150 0.72
SAER3-08 25 1 -16 25.1 26.2 36.9 39.3 3.9 570 7.8 1130 15.7 2280 205 0.90
SAER3-09 31.5 1-1/4 -20 31.4 32.9 42.9 46.0 2.6 380 5.2 750 10.5 1520 250 1.07

SAE 100R4 Wire Inserted Hydraulic Suction Hose

Introduction

SAE 100R4 wire inserted low pressure hydraulic hose is frequently applied to suction & return line, anti-static delivery line, and vacuum applications for petroleum-based and water-based hydraulic fluids. It is constructed with an inner tube of oil-resistant synthetic rubber, a reinforcement consisting of a ply, or plies, of woven or braided textile fibers with a suitable spiral of body wire, and an oil and weather resistant synthetic rubber cover.

A drawing of SAE 100R4 hydraulic hose and we can see one-braid of fiber clearly.

SAEH-07: SAE 100R4 hydraulic hose drawing.

A piece of SAE 100R4 hydraulic hose and we can see the specs printing on the hose surface.

SAEH-08: SAE 100R4 hydraulic hose.

Construction

  • Tube: black, oil resistant, Nitrile (NBR).
  • Reinforcement: a ply or piles of woven or braided textile fibers with a suitable spiral of body steel wire.
  • Cover: an oil and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F).
Table 4: SAE 100R4 Wire Inserted Hydraulic Suction Hose Technical Specification
Item Size SAE Size I.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. max. MPa psi MPa psi MPa psi mm kg/m
SAER4-01 19 3/4 -12 18.2 19.8 34.9 2.1 305 4.2 610 8.4 1210 125 0.92
SAER4-02 25 1 -16 24.6 26.2 41.3 1.7 250 3.5 510 7 1015 150 1.10
SAER4-03 31.5 1-1/4 -20 30.6 33 50.8 1.4 200 2.8 410 5.6 810 200 1.30
SAER4-04 38 1-1/2 -24 36.9 39.3 57.2 1.05 150 2.1 305 4.2 610 255 1.80
SAER4-05 51 2 -32 49.2 52.4 69.9 0.7 100 1.4 200 2.8 410 300 2.23
SAER4-06 63 2-1/2 -40 61.9 65.1 82.6 0.4 60 0.85 120 1.7 250 355 3.23
SAER4-07 76 3 -48 74.6 77.8 95.3 0.4 60 0.8 120 1.6 230 460 4.25
SAER4-08 89 3-1/2 -56 87.3 90.5 107.9 0.3 40 0.6 90 1.25 180 530 5.05
SAER4-09 102 4 -64 100 103.2 120.7 0.25 40 0.5 70 1 145 610 5.60

SAE 100R5 Single Wire Braided Textile Covered Hydraulic Rubber Hose

Introduction

SAE 100R5 single wire braid and textile covered hydraulic rubber hoses are widely used in medium pressure applications. They are suitable for conveying petroleum-based hydraulic oil, air and water with specified pressure to air brakes, power steering, turbo oil lines and tilt cab cylinders. Oil resistant tube, single wire braid reinforcement and fiber braided cover contributes high performance. Fabric braids should be resistant to oils and mildew.

A drawing of SAE 100R5 hydraulic hose and we can see one-braid high tensile steel wire.

SAEH-09: SAE 100R5 hydraulic hose drawing.

A black color SAE 100R5 hydraulic hose and we can see the smooth and bright fiber braid cover.

SAEH-10: SAE 100R5 hydraulic hose.

Construction

  • Tube: oil resistant synthetic rubber.
  • Reinforcement: A single high tensile steel wire braid.
  • Cover: A fiber braided cover.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F).
Table 5: SAE 100R5 Steel Wire Reinforced Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P Min. B.R. Weight
mm inch dash min. max. min. max. MPa psi MPa psi MPa psi mm kg/m
SAER5-01 5 3/16 -3 4.8 5.5 12.7 13.7 21.0 3045 42 6090 84 12180 75 0.24
SAER5-02 6.3 1/4 -4 6.4 7.2 14.3 15.3 21.0 3045 42 6090 84 12180 85 0.28
SAER5-03 8 5/16 -5 7.9 8.7 16.7 17.6 15.7 2270 31.5 4570 63 9135 100 0.35
SAER5-04 11 1-3/32 -6 10.3 11.1 18.9 20 14.0 2030 28 4060 56 8120 115 0.38
SAER5-05 12.5 1/2 -8 12.7 13.7 22.8 24 12.2 1770 24.5 3550 49 7105 140 0.51
SAER5-06 16 5/8 -10 15.9 17 26.8 28 10.5 1520 21 3045 42 6090 165 0.68
SAER5-07 22 7/8 -14 22.2 23.3 30.6 32.2 5.6 810 11.2 1620 22.4 3250 185 0.70
SAER5-08 29 1-1/8 -22 28.6 29.8 37.3 38.9 4.3 620 8.7 1260 17.5 2540 230 0.80
SAER5-09 35 1-3/8 -26 34.9 36.1 43.7 45.2 3.5 510 7 1015 14 2030 265 0.93
SAER5-10 46 1-13/16 -30 46.0 47.2 55.2 57.6 2.4 350 4.9 700 9.8 1420 335 1.32
SAER5-11 60 2-3/8 -38 60.3 61.9 71.8 74.2 2.4 350 4.9 700 9.8 1420 610 2.96
SAER5-12 76 3 -48 76.2 77.8 89.3 91.7 1.4 200 2.8 410 5.6 810 840 4.10

SAE 100R6 Fiber Reinforced (Nonmetallic) Hydraulic Rubber Hose

Introduction

SAE 100R6 textile braided hydraulic hose is applied to the low pressure conditions, especially where tight routing is urgently required. It is also including return & suction lines, power steering return hoses, lube lines and air lines without brake applications.

It consists of an inner tube of oil-resistant synthetic rubber, one-braid suitable textile yarn and an oil and weather resistant synthetic rubber cover.

A drawing of SAE 100R6 hydraulic hose and we can see one-braid fiber.

SAEH-11: SAE 100R6 hydraulic hose drawing.

Three pieces of SAE 100R6 hydraulic hoses with fittings.

SAEH-12: SAE 100R6 hydraulic hose with fittings.

Construction

  • Tube: oil resistant synthetic rubber.
  • Reinforcement: one-braid suitable fiber.
  • Cover: oil and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C (-40 °F to +212 °F)
Table 6: SAE 100R6 Fiber Reinforced (Nonmetallic) Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. max. MPa psi MPa psi MPa psi mm kg/m
SAER6-01 5 3/16 -3 4.2 5.4 10.3 3.5 510 7 1015 14 2030 50 0.10
SAER6-02 6.3 1/4 -4 5.6 7.2 11.9 2.8 410 5.6 810 11.2 1620 65 0.13
SAER6-03 8 5/16 -5 7.2 8.8 13.5 2.8 410 5.6 810 11.2 1620 75 0.15
SAER6-04 10 3/8 -6 8.7 10.3 15.1 2.8 410 5.6 810 11.2 1620 75 0.18
SAER6-05 12.5 1/2 -8 11.9 13.5 19.0 2.8 410 5.6 810 11.2 1620 100 0.26
SAER6-06 16 5/8 -10 15.1 16.7 22.2 2.4 350 4.8 710 9.8 1420 125 0.34
SAER6-07 19 3/4 -12 18.3 19.9 25.4 2.1 310 4.2 610 8.4 1220 150 0.40

SAE 100R7 Thermoplastic Hydraulic Hose

Introduction

SAE 100R7 non-conductive thermoplastic hydraulic hose is available for applications where there are potential to contact with high voltage sources. Nylon tube is compatible with petroleum, water and synthetic based hydraulic fluids for mobile equipment, lube lines, blowout preventers and hydraulic lifts where nonconductive character is necessary. It consists of a thermoplastic inner tube resistant to hydraulic fluids with suitable synthetic-fiber reinforcement and a hydraulic fluid and weather resistant thermoplastic cover.

A drawing of SAE 100R7 hydraulic hose shows fiber braid reinforcement and thermoplastic inner tube.

SAEH-13: SAE 100R7 hydraulic hose drawing.

A hand holding two SAE 100R7 hydraulic hoses and they show the section structure clearly.

SAEH-14: SAE 100R7 hydraulic hose.

Construction

  • Tube: A thermoplastic inner tube of resistant to hydraulic fluids.
  • Reinforcement: Reinforced with suitable synthetic fiber.
  • Cover: A hydraulic fluid and weather resistant thermoplastic.
  • Temperature: -40 °C to +93 °C (-40 °F to +199.4 °F).
Table 7: SAE 100R7 Thermoplastic Hydraulic Hose Technical Specification
Item Size SAE Size I.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. max. MPa psi MPa psi MPa psi mm kg/m
SAER7-01 5 3/16 -3 4.6 5.4 11.4 21 3045 42 6090 84 12180 90 0.073
SAER7-02 6.3 1/4 -4 6.2 7.0 13.7 19.2 2780 38.5 5580 77 11165 100 0.090
SAER7-03 8 5/16 -5 7.7 8.5 15.6 17.5 2535 35 5075 77 10150 115 0.128
SAER7-04 10 3/8 -6 9.3 10.3 18.4 15.7 2275 31.5 4565 63 9135 125 0.155
SAER7-05 12.5 1/2 -8 12.3 13.5 22.5 14 2030 28 4060 56 8120 180 0.224
SAER7-06 16 5/8 -10 15.5 16.7 25.8 10.5 1520 21 3045 42 6090 205 0.277
SAER7-07 19 3/4 -12 18.6 19.8 28.6 8.7 1260 17.5 2535 35 5075 240 0.330
SAER7-08 25 1 -16 25.0 26.4 36.7 7 1015 14 2030 28 4060 300 0.403

SAE 100R8 High Pressure Thermoplastic Hydraulic Hose

Introduction

SAE 100R8 high pressure thermoplastic hydraulic hose is used in non-conductive applications where there are potential of contact with high voltage sources, such as blowout preventers, lube lines and construction machinery. It consists of a thermoplastic inner tube resistant to hydraulic fluids with suitable synthetic-fiber reinforcement and a hydraulic fluid and weather resistant thermoplastic cover.

A drawing of SAE 100R8 hydraulic hose with fiber braid reinforcement and thermoplastic inner tube.

SAEH-15: SAE 100R8 hydraulic hose drawing.

A roll of SAE 100R8 hydraulic hose shows the detail section of inner tube and reinforcement layer.

SAEH-16: SAE 100R8 hydraulic hose.

Construction

  • Tube: A thermoplastic inner tube of resistant to hydraulic fluids.
  • Reinforcement: Reinforced with suitable synthetic fiber.
  • Cover: A hydraulic fluid and weather resistant thermoplastic.
  • Temperature: -40 °C to +93 °C (-40 °F to +199.4 °F)
Table 8: SAE 100R8 High Pressure Thermoplastic Hydraulic Hose Technical Specification
Item Size SAE Size I.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. max. MPa psi MPa psi MPa psi mm kg/m
SAER8-01 5 3/16 -3 4.6 5.4 14.6 35 5075 70 10150 140 20300 90 0.086
SAER8-02 6.3 1/4 -4 6.2 7.0 16.8 35 5075 70 10150 140 20300 100 0.097
SAER8-03 10 3/8 -6 9.3 10.3 20.3 28 4060 56 8120 112 16240 125 0.178
SAER8-04 12.8 1/2 -8 12.3 13.5 24.6 24.5 3550 49 1705 98 14210 180 0.215
SAER8-05 16 5/8 -10 15.5 16.7 29.8 19.2 2780 38.5 2280 77 11165 205 0.312
SAER8-06 19 3/4 -12 18.6 19.8 33 15.7 2275 31.5 4565 63 9135 240 0.360
SAER8-07 25 1 -16 25.0 26.4 38.6 14 2030 28 4060 56 8120 300 0.505

SAE 100R9 High Pressure Four Spiral Steel Wire Hydraulic Rubber Hose

Introduction

SAE 100R9 high pressure four spiral steel wire hydraulic rubber hose consist of an inner tube of oil resistant synthetic rubber, four-spiral steel wire reinforcement and oil and weather resistant synthetic rubber cover. Spiral hydraulic hose shares outstanding kick resistance, impulse resistance and can support surge pressure.

SAE 100R9 high pressure four spiral steel wire hydraulic rubber hose is widely used in applications where high pressure, high abrasion and kick resistance are urgently required, petroleum base hydraulic fluids within a temperature ranging from -40 °C to +100 °C.

A drawing of SAE 100R9 hydraulic hose with four-spiral high tensile steel wire.

SAEH-17: SAE 100R9 hydraulic hose drawing.

Three pieces o f SAE 100R9 hydraulic  hoses with fittings on one side.

SAEH-18: SAE 100R9 hydraulic hose.

Construction

  • Tube: High quality synthetic rubber compounds.
  • Reinforcement: Four-spiral high tensile steel wire.
  • Cover: Abrasion and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C(-40 °F to +212 °F).
Table 9: SAE 100R9 High Pressure Four Spiral Steel Wire Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
A AT
mm inch dash min. max. min. max. min. max. max. MPa psi MPa psi MPa psi mm kg/m
SAER9-01 10 3/8 -6 9.3 10.1 16.9 18.0 20.6 22.2 21.1 31.5 4570 63 9135 126 18270 125 0.70
SAER9-02 12.5 1/2 -8 12.3 13.5 19.4 21.0 23.8 25.4 24.3 28 4060 56 8120 112 16240 180 0.83
SAER9-03 19 3/4 -12 18.6 19.8 26.6 28.2 30.6 32.2 31.9 21 3045 42 6090 84 12180 240 1.30
SAER9-04 25 1 -16 25.0 26.4 34.5 36.1 38.5 40.9 40.5 21 3045 42 6090 84 12180 300 1.70
SAER9-05 31.5 1-1/4 -20 31.4 33.0 43.3 45.6 49.2 52.4 50.7 17.5 2540 35 5075 70 10150 420 3.08
SAER9-06 38 1-1/2 -24 37.7 37.7 49.6 52.0 55.6 58.7 14 2030 28 4060 56 8120 500 4.30
SAER9-07 51 2 -32 50.4 50.4 63.9 66.2 69.9 73.0 14 2030 28 4060 56 8120 660 5.63

SAE 100R12 Heavy Duty High Four Spiral Steel Wire Hydraulic Rubber Hose

Introduction

SAE 100R12 heavy duty hydraulic hose is reinforced by four layers of spiral steel wire in alternating directions which can balance pressure and containment forces. Spiral wire reinforcement is ideal for high-impulse and high abrasion resistance applications. This section covers hose for using with petroleum based hydraulic fluids within a temperature ranging from -40 °C to +121 °C.

It consists of an inner tube of oil-resistant synthetic rubber, four spiral plies of heavy wire wrapped in alternating directions, and an oil and weather resistant synthetic rubber cover. A ply, or braid, of suitable material may be used over the inner tube and/or over the wire reinforcement to fasten the synthetic rubber to the wire.

A drawing of SAE 100R12 hydraulic hose shows four-spiral high tensile steel wire.

SAEH-19: SAE 100R12 hydraulic hose.

A section structure of SAE 100R12 hydraulic hose.

SAEH-20: SAE 100R12 hydraulic hose.

Construction

  • Tube: oil resistant synthetic rubber compounds.
  • Reinforcement: four spiral piles of steel wire wrapped in alternating directions.
  • Cover: oil and weather resistant synthetic rubber.
  • Temperature: -40 °C to +120 °C (-40 °F to +250 °F).
Table 10: SAE 100R12 Heavy Duty High Four Spiral Steel Wire Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. min. max. min. max. MPa psi MPa psi MPa psi mm kg/m
SAER12-01 10 3/8 -6 9.3 10.1 16.6 17.8 19.5 21.0 28 4060 56 8120 112 16240 125 0.70
SAER12-02 12.5 1/2 -8 12.3 13.5 19.9 21.5 23.0 24.6 28 4060 56 8120 112 16240 180 0.83
SAER12-03 16 5/8 -10 15.5 16.7 23.8 25.4 26.6 28.2 28 4060 56 8120 112 16240 200 1.12
SAER12-04 19 3/4 -12 18.6 19.8 26.9 28.4 29.9 31.5 28 4060 56 8120 112 16240 240 1.43
SAER12-05 25 1 -16 25.0 26.4 34.1 35.7 36.8 39.2 28 4060 56 8120 112 16240 300 2.00
SAER12-06 31.5 1-1/4 -20 31.4 33.0 42.7 45.1 45.4 48.6 21 3045 42 6090 84 12180 420 2.80
SAER12-07 38 1-1/2 -24 37.7 39.3 49.2 51.6 51.9 55.0 17.5 2540 35 5075 70 10150 500 3.40
SAER12-08 51 2 -32 50.8 52.0 62.5 64.8 65.1 68.3 17.5 2540 35 5075 70 10150 640 4.25

SAE 100R13 Heavy Duty High Multiple Spiral Steel Wire Hydraulic Rubber Hose

Introduction

SAE 100R13 heavy duty high multiple spiral steel wire hydraulic hoses are reinforced with four layers of spiral wires in alternation directions to provide extremely high working pressure. It is constructed with an inner tube of oil resistant synthetic rubber, followed by multiple spiral plies of heavy wire wrapped in alternating directions, and concluding with an oil and weather resistant synthetic rubber cover. A ply, or braid, of suitable material may be used over the inner tube and/or over the wire reinforcement to fasten the synthetic rubber to the wire.

A drawing of SAE 100R13 hydraulic hose shows six-spiral steel wires.

SAEH-21: SAE 100R13 hydraulic hose drawing.

A detailed section structure of SAE 100R13 hydraulic hose with six-spiral steel wires.

SAEH-22: SAE 100R13 hydraulic hose.

Construction

  • Tube: black, oil resistant, Neoprene (CR).
  • Reinforcement: multiple spiral piles of steel wires wrapped in alternating directions.
  • Cover: oil and weather resistant synthetic rubber.
  • Temperature: -40 °C to +120 °C (-40 °F to +250 °F).
Table 11: SAE 100R13 Heavy Duty High Multiple Spiral Steel Wire Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. min. max. min. max. MPa psi MPa psi MPa psi mm kg/m
SAER13-01 19 3/4 -12 18.6 19.8 28.2 29.8 31.0 33.2 35 5075 70 10150 140 20300 240 2.10
SAER13-02 25 1 -16 25.0 26.4 34.9 36.4 37.6 39.8 35 5075 70 10150 140 20300 300 2.88
SAER13-03 31.5 1-1/4 -20 31.4 33.0 45.6 48.0 48.3 51.3 35 5075 70 10150 140 20300 420 4.20
SAER13-04 38 1-1/2 -24 37.7 39.3 53.1 55.5 55.8 58.8 35 5075 70 10150 140 20300 500 5.00
SAER13-05 51 2 -32 50.4 52.0 66.9 69.3 69.5 72.7 35 5075 70 10150 140 20300 640 7.00

SAE 100R14 PTFE Lined Hydraulic Hose

Introduction

SAE 100R14 PTFE hydraulic hose for use with petroleum based and synthetic based hydraulic fluids within a temperature ranging from -54 °C to +204 °C. It can also be used with water based hydraulic fluids within the environments, where the temperature should be agreed upon by the manufactures of both the hose and the fluid. It has two types for different application. Type A consists of an inner tube of Polytetrafluoroethylene (PTFE) reinforced with a single braid of type 303XX stainless steel.

Type B has the same construction as Type A, but type B has the additional feature of an electrically-conductive inner surface to prevent buildup of an electrostatic charge.

A drawings of SAE 100R14 hydraulic hose with PTFE inner tube and stainless steel braid wire.

SAEH-23: SAE 100R14 hydraulic hose drawing.

Four SAE 100R14 hydraulic hoses and two types of inner tube: smooth and spiral inner tube.

SAEH-24: Two inner tube types of SAE 100R14 hydraulic hoses.

Construction

  • Tube: polytetrafluoroethylene (PTFE).
  • Reinforcement: a single braid of 303XX series stainless steel wire.
  • Cover: one stainless steel wire braid.
  • Temperature: -54 °C to +204 °C (-65 °F to +400 °F)
Table 12: SAE 100R14 PTFE Lined Hydraulic Hose Technical Specification
Item Size SAE Size I.D. O.D. Max. W.P Proof Pressure P.P. Min. B.P. Min. B.R.
mm dash min. max. min. max. MPa psi MPa psi MPa psi mm
SAER14-01 3.2 -3 2.8 3.8 5.3 6.8 10.5 1523 41.4 6003 82.7 11992 40
SAER14-02 5 -4 4.4 5.2 7.1 8.2 10.5 1523 34.5 5003 68.9 9990 50
SAER14-03 6.3 -5 6.0 6.9 8.9 10.1 10.5 1523 31.0 4495 62.0 8990 75
SAER14-04 8 -6 7.5 8.4 10.4 11.6 10.5 1523 27.6 4002 55.2 8004 100
SAER14-05 10 -7 9.1 10.0 12.2 13.4 10.5 1523 24.1 3495 48.3 7004 125
SAER14-06 11 -8 9.9 10.9 12.9 14.3 7 1015 20.7 3002 41.4 6003 135
SAER14-07 12.5 -10 12.3 13.3 15.3 16.8 5.6 812 20.7 3002 41.4 6003 165
SAER14-08 16 -12 15.3 16.5 18.6 20.1 5.6 812 17.2 2494 34.5 5003 200
SAER14-09 19 -14 18.4 19.6 21.3 23.3 5.6 812 16.8 2436 27.6 4002 230
SAER14-10 22 -16 21.4 23.0 24.6 26.9 5.6 812 12.1 1755 24.1 3495 230
SAER14-11 25 -18 24.6 26.2 27.8 29.8 5.6 812 12.1 1755 24.1 3495 300
SAER14-12 29 -20 27.8 29.4 31.9 31.9 4.2 609 8.6 1247 17.2 2494 410

SAE 100R15 Heavy Duty High Pressure Impulse Spiral Steel Wire Hydraulic Rubber Hose

Introduction

SAE 100R15 high pressure hydraulic hose is reinforced by four or six alternating layers of spiral and high tensile steel wires. It is very popular in logging, construction, mining, agriculture and oil field equipment, because it can work constantly under high pressure.

It consists of an inner tube of oil-resistant synthetic rubber, multiple spiral plies of heavy wire wrapped in alternating directions, and an oil and weather resistant rubber cover. A ply, or braid, of suitable material may be used over or within the inner tube and/or over the wire reinforcement to anchor the synthetic rubber to the wire.

drawings of SAE 100R15-4 and SAE 100R14-6 hydraulic hoses.

SAEH-25: Two types of SAE 100R15 hydraulic hoses.

Six SAE 100R15 hydraulic hoses show the section structure.

SAEH-26: SAE 100R15-6 hydraulic hose.

Construction

  • Tube: black, oil resistant, Neoprene (CR).
  • Reinforcement: multiple spiral piles of heavy steel wire wrapped in alternating directions.
  • Cover: oil and weather resistant synthetic rubber.
  • Temperature: -40 °C to +120 °C (-40 °F to +250 °F).
Table 13: SAE 100R15 Heavy Duty High Pressure Impulse Spiral Steel Wire Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. max. max. MPa psi MPa psi MPa psi mm kg/m
SAER15-01 10 3/8 -6 9.3 10.1 20.3 23.3 42 6090 84 12180 168 24360 150 0.80
SAER15-02 12.7 1/2 -8 12.3 13.5 24.0 26.8 42 6090 84 12180 168 24360 200 0.95
SAER15-03 19 3/4 -12 18.6 19.8 32.0 36.1 42 6090 84 12180 168 24360 265 1.85
SAER15-04 25 1 -16 25.0 26.4 38.9 42.9 42 6090 84 12180 168 24360 330 2.90
SAER15-05 31.5 1-1/4 -20 31.4 33.0 48.4 51.5 42 6090 84 12180 168 24360 445 4.20
SAER15-06 38 1-1/2 -24 37.7 39.3 56.3 59.6 42 6090 84 12180 168 24360 530 5.60

SAE 100R16 Compact High Pressure One and Two Steel Wire Hydraulic Rubber Hose

Introduction

SAE 100R16 compact high pressure hydraulic rubber hose consists of an inner tube of oil resistant synthetic rubber, one or two braids of steel wire reinforcement, and an oil and weather resistant synthetic rubber cover. A ply, or braid, of suitable material may be used over the inner tube and/or over the wire reinforcement to anchor the synthetic rubber to the wire.

SAE 100R16 compact high pressure hydraulic rubber hose has priority when you choose hydraulic hoses for narrow routing spacing, it is applied for backhoe, farm tractor, forklift truck, dump truck, mobile equipment. It is also widely used with petroleum base hydraulic fluids within -40 °C to +100 °C.

Two drawings of SAE 100R16 hydraulic hoses: SAE 100R16-1 and SAE 100R16-2.

SAEH-27: SAE 100R16 hydraulic hose drawing.

A SAE 100R16 hydraulic hose with two-braid steel wire reinforcement and specs on the surface.

SAEH-28: SAE 100R16-2 hydraulic hose.

Construction

  • Tube: oil resistant synthetic rubber.
  • Reinforcement: steel wire reinforcement according to hose design (one or two braids).
  • Cover: oil and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C(-40 °F to +212 °F).
Table 14: SAE 100R16 Compact High Pressure One and Two Steel Wire Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. max. max. MPa psi MPa psi MPa psi mm kg/m
SAER16-01 6.3 1/4 -4 6.2 7.0 12.3 14.5 35 5075 70 10150 140 20300 50 0.30
SAER16-02 8 5/16 -5 7.7 8.5 13.3 15.7 30 4305 59.5 8625 119 17255 55 0.34
SAER16-03 10 3/8 -6 9.3 10.1 15.9 18.8 33 4060 56 8120 112 16240 65 0.42
SAER16-04 12.5 1/2 -8 12.3 13.5 19.0 22.0 27.5 3550 49 7105 98 14210 90 0.54
SAER16-05 16 5/8 -10 15.5 16.7 22.6 25.4 25 2780 38.5 5580 77 11165 100 0.68
SAER16-06 19 3/4 -12 18.6 19.8 26.3 29.0 21.5 2275 31.5 4565 63 9135 120 0.80
SAER16-07 25 1 -16 25.0 26.4 34.0 36.6 16.5 2030 28 4060 56 8120 150 1.15
SAER16-08 31.5 1-1/4 -20 31.4 33.0 41.9 44.3 12.5 1635 22.7 3290 45.5 6595 210 1.83

SAE 100R17 Compact 21 MPa Maximum Working Pressure Hydraulic Rubber Hose

Introduction

SAE 100R17 Compact hydraulic rubber hose has smaller bend radius and is ideal for tight routing where hose space is limited. It provides continuous working pressure for mining equipment, logging equipment, material handling and farm tractor.

It is consist of an inner tube of oil resistant synthetic rubber, steel wire reinforcement according to hose design (one or two braids), and an oil and weather resistant synthetic rubber cover. A ply or braid of suitable material may be used over the inner tube or over the wire reinforcement to anchor the synthetic rubber to the wire.

Two drawings of SAE 100R17 hydraulic hoses with one or two braids of high tensile steel wires.

SAEH-29: SAE 100R17 hydraulic hose drawings

A roll of SAE 100R17 hydraulic hose with clearly two-braid high tensile steel wire reinforcement.

SAEH-30: SAE 100R17 hydraulic hose.

Construction

  • Tube: oil resistant synthetic rubber.
  • Reinforcement: steel wire reinforcement according to hose design (one or two braids).
  • Cover: oil and weather resistant synthetic rubber.
  • Temperature: -40 °C to +100 °C(-40 °F to +212 °F).
Table 15: SAE 100R17 Compact 21 MPa Maximum Working Pressure Hydraulic Rubber Hose Technical Specification
Item Size SAE Size I.D. Reinforcement W.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight
mm inch dash min. max. max. max. MPa psi MPa psi MPa psi mm kg/m
SAER17-01 6.3 1/4 -4 6.2 7.0 11.0 13.2 21 3045 42 6090 84 12180 50 0.169
SAER17-02 8 5/16 -5 7.7 8.5 13.0 15.0 21 3045 42 6090 84 12180 55 0.210
SAER17-03 10 3/8 -6 9.3 10.1 15.0 17.0 21 3045 42 6090 84 12180 65 0.254
SAER17-04 12.5 1/2 -8 12.3 13.5 18.8 21.1 21 3045 42 6090 84 12180 90 0.466
SAER17-05 16 5/8 -10 15.5 16.7 23.6 25.9 21 3045 42 6090 84 12180 100 0.586
SAER17-06 19 3/4 -12 18.6 19.8 27.7 30.3 21 3045 42 6090 84 12180 120 0.749
SAER17-07 25 1 -16 25.0 26.4 35.6 35.6 21 3045 42 6090 84 12180 150 1.457

When you contact us, please provide your detail requirements.

That will help us give you a valid quotation.